Comment: (Length+width) x height = size. The piece quantity includes pieces up and down and pallet forward and back.Automatic saw (AS)
NQ: Enter the number of slices / work setup.
PLB: Enter 1 for particle board, otherwise 0.
FCT: Enter the factor (Number of men. You can enter decimals here).
Table mill cutter (TM)
FL: Enter the feed length in mm.
FS: Enter the feed speed (mm / minute).
FCT: Enter the factor. (Number of men. You can enter decimals here).
Wide strip buffer (WSB)
FL: Enter the feed length in mm.
FS: Enter the feed speed in mm / minute.
LQ: Enter the quantity by width through the buffer.
FCT: Enter the factor (Number of men. You can enter decimals here).
Center pin (CP)
MT: Enter the machine type: 1 = center pin drill - single, 2 = center pin drill - multi-hole, 3 = hinge mounting.
NQ: Enter the number of sides that will be drilled in the same pace. Enter 0 for machine type MT = 2.
PQ: Enter the pace quantity (piece up and down) that is needed to drill the piece.
DD: Enter the drill depth in mm.
HAQ: Hinge/attachment quantity. Enter the quantity of piece moves to mount the hinges or attachments. Enter 0 for machine type MT = 1.
HQ: Enter the number of holes.
FCT: Enter the factor (Number of men. You can enter decimals here).
Double pin (DP)
MT: Enter the feed length in mm.
FS: Enter the feed speed in mm / minute.
PQ: Enter the pace quantity (piece up and down).
FCT: Enter the factor. (Number of men. You can enter decimals here).
Automatic edging (AED)
FL: Enter the feed length in mm.
FS: Enter the feed speed in mm / minute.
PQ: Enter the pace quantity that the piece is run through the automatic edging machine.
FCT: Enter the factor (Number of men. You can enter decimals here).
Edge buffer (EB)
FL: Enter the feed length in mm.
FS: Enter the feed speed in mm / minute.
BQ: Enter the quantity (number of times) the piece goes through the buffer.
FCT: Enter the factor (Number of men. You can enter decimals here).
Cutting (C)
CA: Enter the piece's cut area in mm2.
EC: Enter 1 for edge cutting, otherwise 0.
FCT: Enter the factor (Number of men. You can enter decimals here).
Lacquer line (LL)
FL: Enter the feed length in mm.
FS: Enter the feed speed in mm / minute.
LQ: Enter the quantity by width through the lacquer line.
FCT: Enter the factor (Number of men. You can enter decimals here).
Lathe saw - plane (LP)
LQ: Enter the lathe quantity.
FS: Enter the feed speed in mm / minute.
FCT: Enter the factor (Number of men. You can enter decimals here).
Gluing (GLU)
NQ: Enter the side quantity with plywood.
FCT: Enter the factor (Number of men. You can enter decimals here).
NC-Drill (NCD)
FL: Enter the feed length in mm.
FS: Enter the feed speed in mm / minute.
NQ: Enter the start quantity.
FQ: Enter the feed quantity.
DD: Enter the drill depth in mm.
FCT: Enter the factor. (Number of men. You can enter decimals here).
NC-Mill (NCM)
ML: Enter the milling length in mm.
FS: Enter the feed speed in mm / minute.
NQ: Enter the start quantity.
TC: Enter the quantity of tool changes.
FCT: Enter the factor. (Number of men. You can enter decimals here).
Vertical drill (VD)
PQ: Enter the pace quantity (piece up and down).
HQ: Enter the quantity of holes that will be drilled.
DD: Enter the drill depth in mm.
HG: Enter 1 for homogenous material, otherwise 0.
CK: Enter 1 if you must check straightness, otherwise 0.
FCT: Enter the factor. (Number of men. You can enter decimals here).
Nailing (NA)
Comment: (Length+width) x height = size. The piece quantity includes pieces up and down and pallet forward and back.
Q1: Enter the quantity of pieces <200.
Q2: Enter the quantity of pieces <500.
Q3: Enter the quantity of pieces <1000.
Q4: Enter the quantity of pieces <1500.
Q5: Enter the quantity of pieces <2000.
Q6: Enter the quantity of pieces <3000.
NQ: Enter the total nail quantity.
TQ: Enter 0 if the piece is nailed on one side and 1 if it is nailed on both sides.
Sawing (SAW)
PQ: Enter the pace quantity (piece up and down).
TQ: Enter the quantity of turns (sides).
SL: Enter the total saw length in mm.
FCT: Enter the factor (Number of men. You can enter decimals here).